QCA Spa Jewel +3 Series Owner's Manual download pdf (Page 6)

Standby Mode

Pressing “Warm” or “Cool” then “Jets 2” will turn

off all spa functions temporarily. This is helpful

when changing a filter. Press any button to exit

Standby mode.

Jets 1

Press the “Jets 1” button once to turn pump 1 on,

again to switch to high-speed. Pressing for a third

time turns pump 1 off. If left running, the low

speed turns off after 2 hours and the high speed

turns off after 15 minutes.

The low-speed of pump 1 runs when the blower or

any other pump is on. It may also activate for at

least 2 minutes every 30 minutes to detect the spa

temperature (polling) and then to heat to the set

temperature if needed, depending upon mode.

When the low speed turns on automatically, it

cannot be deactivated from the panel; however, the

high speed may be started.

Jets 2

Press the “Jets 2” button once to turn pump 2 on to

high-speed. Pressing once more, turns off pump 2.

If left running, the pump will turn off after 15

minutes.

Blower

Press the “Blower” button to turn on, twice to turn

on low speed, three times to turn on medium speed

and a fourth time to turn on high-speed. Pressing

once more will turn the blower off.

If left on, the blower will automatically turn off

after 15 minutes.

Light

Press the “Light” button to turn the spa light on

and off. Will also control optional LED lighting.

Preset Filter Cycles

On all systems, the pump and the ozone generator

will run during filtration. At the start of each filter

cycle, the blower will run on highest speed for 30

seconds to clean out the air channels. The low-

speed of pump 2 will run for 5 minutes.

There are two filter cycles per day. The start/end

times of each cycle are programmable. To

program, set time as instructed above, then press

“Mode/Prog” to advance to the next setting (or to

exit after the last setting). The default filter cycles

are as follows:

The first filter cycle is automatically activated at

8:00 AM and operates the pump until 10:00 AM.

The filter 1 indicator icon will light when filter 1 is

running.

The second filter cycle is automatically activated

at 8:00 PM and operates the pump until 10:00 PM.

The filter 2 indicator icon will light when filter 2 is

running.

Optional Filter Cycle Programming

You are not required to set filter cycles; however,

it is an option available to you. To change the filter

cycle settings:

Press “Time” “Mode/Prog” “Mode/Prog”

“Mode/Prog” within 3 seconds. You will see the

“SET FILTER 1” and a flashing “START TIME”

icon appear on the display.

Press “Up” or “Down” to choose the filter start

time hour. Enter the hour by pressing

“Mode/Prog”. Press “Up” or “Down” to choose the

filter start time minutes. Each press changes the

start time by 5 minutes.

Enter the minutes by pressing “Mode/Prog.”

Press “Mode/Prog” to see the “SET FILTER 1”

and a flashing “END TIME” icon. Adjust the time

as done above.

Press “Mode/Prog” to see the “SET FILTER 2”

(PM cycle) and a flashing “START TIME” icon.

Proceed as above.

Press “Mode/Prog” to see “SET FILTER 2” and a

flashing “END TIME” icon. Adjust the time as

done above.

Pressing “Mode/Prog” will enter the new filter

cycle times into the system and display the current

water temperature.

Pressing “Time” at any time during this

programming sequence will save the values

entered up to that point and exit programming.

If you would like to select continuous filtration, set

the filter 1 start and end times to be the exact same

time.

Clean-up Cycle

When the pump or blower is turned on by a button

press, a clean-up cycle begins 30 minutes after the

pump or blower is turned off or times out. The

pump and the ozone generator** will run for one

hour.

Freeze Protection

If the temperature sensors detect a drop to 44° F

(approximately 6.7° C) within the heater, then the

pump automatically activates to provide freeze

protection. The equipment stays on until 4 minutes

after the sensors detect that the spa temperature has

risen to 45° F (approximately 7.2°C) or higher. In

colder climates, an optional additional freeze

sensor may be added to protect against freeze

conditions that may no be sensed by the standard

sensors. Aux freeze sensor protection acts

similarly except t\with the temperature thresholds

determined by the switch and without a 4-minute

delay in turnoff. See you dealer for details.

Locking the Panel

Press “Time” Jets 1” then the “Warm” with in 3

seconds. When locked the PL indicator light will

light. All buttons are frozen except the “Time”

button. To unlock panel, press “Time” “Jets 1”

then “Cool.”

1 2 3 4 5 6 7 8 9 10 11 12 13

Comments to this Manuals

No comments

QCA Spa Jewel +3 Series Owner's Manual Page 6

Comments to this Manuals